ESSENTIAL PLUMBER GUIDE FOR INSTALLING A BATHTUB

Essential Plumber Guide for Installing a Bathtub

Essential Plumber Guide for Installing a Bathtub

Blog Article

Call Today

Presented here down the page you will find lots of outstanding content relating to How to Install a Bathtub Yourself.


Installing A Bathtub
Setting up a bathtub isn't precisely rocket science, but it does need solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently obtainable, the task can move rapidly; if you have to open a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require an assistant to vacate the old tub and embeded in the new one. Make sure you have qualified yourself for the work as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to think about employing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly aid you set up a brand-new bathtub in your bathroom if you have currently purchased a new bathtub as well as don't require to transform the setup of your previous water supply pipelines.
Your devices as well as product checklist must comprise the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the supporting frame supplied with the bath should be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to prevent pressure on the tub.
    Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you make use of all of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its last placement.

    Removing Old Touches


    If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather problematic as a result of the limited access that is usually the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipes have been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
    Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.

    Setting up the Bathtub


    Utilizing the two wood boards under its feet, place the tub in the needed setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub up until the spirit level checks out degree.
    To set up faucets, fit all-time low of the furthest versatile tap port to the suitable supply pipeline by making a compression join; after that do the same for the other tap.
    Switch on the water and inspect all joints and also new pipework for leaks and tighten them if needed. Fill the bath tub and likewise check the overflow electrical outlet as well as the typical outlet for leaks.
    Lastly, repair the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub should wait up until the bathtub has been made use of at least once as this will resolve it right into its last position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and the sink. Safeguard the faucet in place with the supplier provided backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The previous kind ought to be connected to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and also possible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can crack relatively early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    I was brought to that report about How to Install a Bathtub through a friend on another web page. So long as you enjoyed reading our page if you please don't forget to share it. Many thanks for your time. Come back soon.


    Today's problem, today's fix!

    Report this page